Table of Contents
TABLE OF CONTENTS
1.0 — General
1.1 — Scope
1.2 — Definitions
1.3 — References
1.3.1 — Referenced standards and organizations 4
1.3.2 — Cited publications
1.4 — System description
1.5 — Submittals
1.5.1 — Prestressing steel
1.5.2 — Anchorages and couplers
1.5.3 — Sheathing
1.5.4 — PT coating
1.5.5 — Fabrication plant
1.5.6 — Stressing records
1.6 — Fabrication
1.6.1 — General
1.6.1.1 — PTI certified plants
1.6.1.2 — Non-PTI certified plants
1.6.2 — Handling, storage, and shipping
1.6.2.1 — Handling prior to shipping
1.6.2.2 — Storage prior to shipping
1.6.2.3 — Shipping
1.7 — Delivery, handling, and storage
1.7.1 — Delivery
1.7.2 — Handling and storage
1.7.2.1 — Handling
1.7.2.2 — Storage
1.7.2.3 — Exposure
1.7.2.4 — Wedges and anchors
2.0 — Products
2.1 — Prestressing steel
2.1.1 — Mechanical properties
2.1.2 — Thermomechanical treatment
2.1.3 — Traceability
2.1.4 — Testing
2.1.5 — Strand producer records
2.1.6 — Identification
2.1.7 — Packaging, marking, storage,and protection
2.1.8 — Acceptance criteria for surface condition
2.1.9 — Compliance requirements
2.2 — Anchorages and couplers
2.2.1 — Anchorages
2.2.1.1 — Static tests
2.2.1.2 — Fatigue tests
2.2.1.3 — Bearing stresses
2.2.2 — Castings
2.2.3 — Wedges used in anchorages
2.2.4 — Couplers
2.2.5 — Compliance requirements
2.2.5.1 — Conformance testing
2.2.5.2 — Compliance
2.2.6 — Anchorages and couplers in aggressive environments
2.2.6.1 — Anchorages
2.2.6.2 — Encapsulated tendons
2.3 — Sheathing
2.3.1 — General properties
2.3.2 — Minimum thickness and diameter
2.3.2.1 — Minimum thickness
2.3.2.2 — Inside diameter
2.3.2.3 — Appearance
2.3.3 — Fabrication process
2.3.4 — Sheathing coverage
2.3.5 — Encapsulated tendons
2.4 — PT coating
2.4.1 — General properties
2.4.2 — Type of PT coating
2.4.3 — Minimum quantity
2.4.4 — Performance criteria
3.0 — Execution
3.1 — General
3.1.1 — Qualifications and inspection
3.1.2 — Recommended procedures
3.1.3 — Handling
3.1.4 — Protection
3.2 — Tendon installation
3.2.1 — General
3.2.1.1 — Support intervals
3.2.1.2 — Support system
3.2.1.3 — Tendon tolerances
3.2.1.4 — Lateral deviations
3.2.1.5 — Protection
3.2.1.6 — Protection from water
3.2.1.7 — Encapsulated tendons
3.2.2 — Stressing anchorages
3.2.2.1 — Installation
3.2.2.2 — Attachment requirements
3.2.2.3 — Cover requirements
3.2.2.4 — Pocket formers
3.2.2.5 — Encapsulated tendons
3.2.2.6 — Strand tail cover
3.2.3 — Intermediate anchorages
3.2.3.1 — Installation
3.2.3.2 — Placement
3.2.3.3 — Cover requirements
3.2.3.4 — Pocket formers
3.2.3.5 — Encapsulated tendons
3.2.4 — Fixed anchorages
3.2.4.1 — Installation
3.2.4.2 — Wedge seating methodsfor fixed anchorages
3.2.4.3 — Placement
3.2.4.4 — Encapsulated tendons
3.2.5 — Sheathing inspection
3.2.5.1 — Sheathing damage
3.2.5.2 — Repair procedure
3.3 — Concrete placement
3.3.1 — General
3.3.2 — Placement
3.3.3 — Protection of tendons
3.3.4 — Sheathing repairs
3.4 — Tendon stressing
3.4.1 — General
3.4.1.1 — Protection from water
3.4.1.2 — Stressing procedures
3.4.1.3 — Stressing jacks
3.4.2 — Jack calibration
3.4.3 — Elongation measurements
3.5 — Tendon finishing
3.5.1 — General
3.5.1.1 — Cutting of tendon tails
3.5.1.2 — Cutting methods
3.5.2 — Encapsulated tendons
3.5.3 — Stressing pockets
3.5.3.1 — Preparation
3.5.3.2 — Timing